CHAPTER 3 LAB 3-7 OSPF CASE STUDY ANSWERS

Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Configuration Requirements Configure the interfaces in the diagram with the IP addresses shown. Configure area 34 to be a totally stubby area. Notify me of follow-up comments by email. The table does not include any other type of interface, even though a specific router might contain one. Configure the Frame Relay subnets as point-to-point subinterfaces, with the link between HQ and East in area , and the link between HQ and West in area Configure OSPF with interfaces in the areas shown in the diagram.

Modify the link between R2 and R3 to have hello timers and dead timers that are double the default values. Verify that all configurations are operational and functioning according to the guidelines. Configure the router East loopback interfaces to be in area Notify me of follow-up comments by email. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.

Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.

Configure the router East loopback interfaces to be in area To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has.

Design, configure, and test a network that meets all the following requirements:. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab. Configuration Requirements Configure the interfaces in the diagram with the IP addresses shown.

  MANGALYAAN SATELLITE ESSAY

Chapter 3 Lab 3-7 Ospf Case Study Answers

Verify that all configurations are operational and functioning according to the guidelines. Create virtual links as necessary for full connectivity.

chapter 3 lab 3-7 ospf case study answers

Use the addressing scheme shown in the diagram. Notify me of follow-up comments by email.

Chapter 3 Lab Ospf Case Study Answers

Rather than list all combinations of configurations for each router class, this table includes identifiers stuudy the possible combinations of Ethernet and serial interfaces in the device. Notify me of new posts by email. Configure area as an NSSA. Notify me of follow-up comments by email.

CCNP Route Lab 3-5, OSPF Challenge Lab

Explanation of Selected Requirements — Instructor Version The requirement to address a hidden issue in the topology to have full connectivity means that you 3- build a virtual link across area 23 to have area 34 connected to the backbone.

Make sure that all loopback interfaces are advertised with the correct subnet mask.

Figure out the hidden issue in the topology that you need to address lzb have full connectivity. Design, configure, and test a network that meets all the following requirements: Configure the bandwidth to reflect the actual bandwidth of all serial links.

Configure area 34 to be a totally stubby area. Configure R2 to summarize area 20 with the most specific mask possible. To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has.

chapter 3 lab 3-7 ospf case study answers

Modify the link between R2 and R3 to have hello timers and dead timers that are double the default values. Run a Tcl script on all routers to verify that there is connectivity between the IP addresses in the topology. The table does not include any other type of interface, even though a specific router might contain one.

  PHILOSOPHISCHER ESSAY TODESSTRAFE

You can use other routers such as a or and Cisco IOS Software versions if they have comparable capabilities and features. Configure the Frame Relay subnets as point-to-point subinterfaces, with the link between HQ and East in areaand the link between HQ and West in area You can use other routers such as or and Cisco IOS Software versions if they have comparable capabilities and features.

Summarize this area with the most efficient summary.

CCNP Route Lab , OSPF Case Study – Config Router

Osfp OSPF with the networks shown in the diagram. Rather than list all combinations of configurations answes each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device.

The table does not include any other type of interface, even though a specific router might contain one. Make the link between R2 and R3 have a cost of Notify me of new posts by email.

chapter 3 lab 3-7 ospf case study answers

Configure R1 to always originate a default route. Configure OSPF with interfaces in the areas shown in the diagram.

Author: admin